Electrical work can be extremely dangerous if not done properly. As tempting as it may be to rewire your home yourself to save on electrician fees, proceeding without the proper knowledge and precautions can quite literally end in disaster. In this guide, I will walk through all the key steps and safety tips I've learned first-hand for rewiring a home safely without getting shocked or electrocuted.
Understanding Electrical Basics Before Rewiring
Before touching any wires in your home's electrical system, it's absolutely vital that you understand some basic electrical concepts and terminology. This will allow you to work safely and confidently. Some key principles to know are:
-
Voltage - The "pressure" or electrical force measured in volts that pushes current through a wire. In most homes this is typically 120V or 240V.
-
Current - The flow of electrons through a conductor like a wire, measured in amps. More current can be more dangerous.
-
Circuits - A closed loop wiring system that electricity can flow through. Homes have multiple circuits branching off the main electrical panel.
-
Grounding - Providing a safe path for stray electrical current to flow to the earth, preventing shocks. All home wiring should be properly grounded.
-
Short circuit - When electricity flows abnormally between two points with different voltages, often causing sparks, fire hazards, or circuit breaker trips.
-
Amp acity - The maximum current an electrical wire is designed to safely carry without overheating. Check wire amp ratings.
-
Electrical load - The amount of current drawn by appliances and devices on a circuit. Rewiring should account for electrical load.
Having a solid understanding of these core electrical principles is key to safely rewiring any home. Be sure to research any electrical terms or concepts you don't fully grasp before attempting any rewiring project.
Gathering the Right Rewiring Equipment and Tools
To rewire a home yourself, you will need to gather a variety of basic equipment and tools. At minimum, you should have:
-
Wire stripper - For removing insulation on existing and new wires
-
Voltage tester - For safely checking if wires are live before working on them
-
Clamp meter - To measure current and voltage during the rewiring process
-
Cable cutters - Clean cutting and splicing new copper wiring
-
Fish tape - For running new wiring neatly through walls and ceilings
-
Cable stapler - Securing new wiring to studs and joists per code
-
Wire nuts - Twisting wires together securely inside junction boxes
-
Electrical tape - Wrapping wire splices and connections to prevent shorts
-
Headlamp or work lights - Rewiring often takes place in dark spaces like attics
-
Non-contact voltage detector - Detects live voltage before direct contact; safer than testers
I also recommend having PPE like work gloves, insulation masks, safety goggles and electrical-rated tools. It's better to be overprepared with protective gear than risk injuries while handling live wiring.
Killing Power and Testing for Live Wires
Before touching any wiring in your home, it's absolutely vital to kill power to the circuits you'll be working on and verify wires are completely dead. I'd recommend:
-
Turning off the main breaker to kill power to the entire home.
-
Going around the house and switching all circuit breakers to OFF as well, just to be doubly sure.
-
Testing all wires you may touch with a non-contact voltage detector first before touching them to check for any stray electricity.
-
Having a friend or family member flip the main breaker back on briefly while you re-verify all wires are dead with the voltage tester.
Getting complacent by assuming wires are dead without rigorous testing is how lethal mistakes happen. Take the extra time to be absolutely certain by testing live wires in multiple ways.
Pulling Existing Wires Out
Once you've confirmed the wires are 100% dead, you can start removing any outdated wiring. Some tips here include:
-
Label each wire with tape flags as you remove them so you know which runs to which room.
-
Take photos of the wiring before and during removal as reference.
-
Cap all wires with wire nuts as they are removed to avoid stray connections.
-
Coil wires neatly to prevent tangling hazards and store safely.
-
Inspect the emptied wiring paths thoroughly for any insulation damage, exposed conductors, or breach points that could be hazardous when running new wiring. Address any issues first.
-
Remove any abandoned junction boxes no longer needed. Spot check boxes to remain for any defects.
Removing old wiring properly lays the clean foundation needed to run the new wiring safely.
Running and Securing New Wiring
When it comes time to run the new wiring, focus first on neatness, safety and code compliance:
-
Choose wiring with ampacity ratings capable of handling expected electrical loads.
-
Use the correct wire gauge for the amp load and length of run per code minimums.
-
Use nail plates when running wiring through studs to prevent punctures.
-
Keep wiring runs as short and direct as possible.
-
Staple wiring every 4-6 feet and within 1 foot of boxes per code for security.
-
Leave some slack at endpoints to allow for adjustments.
-
Use twist-on wire connectors for solid and reliable splices.
-
Wrap all junction box splices thoroughly with electrical tape.
-
Label all wire runs at endpoints for the circuits they supply.
Taking it slow and methodical is key. Rushing the new wiring job often leads to mistakes and hazards down the road.
Connecting New Wiring to the Panel
One of the most dangerous parts of rewiring is connecting the new wiring to the main electrical panel. To stay safe:
-
Shut off the main breaker again before doing any panel work each day. Verify with a voltage tester that the panel wires are dead.
-
Follow the existing wiring layout conventions to keep things clear. Group hot wires by phase if needed.
-
Ensure wire strip lengths match existing wires for solid contact within connectors.
-
Double check ampacity ratings on all new breakers match the wiring it will supply.
-
Use wire nuts and electrical tape on panel connections for redundancy.
-
Connect grounds first, then neutrals, then hot wires. Reverse the order when removing wiring.
-
Close up the panel fully before re-energizing to prevent any arc flashes.
Rushing while tired leads to wiring errors at the panel. Work slowly and carefully here to prevent disasters down the road.
Testing and Troubleshooting Rewiring Work
After all wiring is run and connected, it's time for testing. But do NOT energize the entire system all at once. Follow these safer steps instead:
-
With the main breaker still off, turn on individual circuits one at a time to test. Address any issues.
-
Check for secure ground connections by pressing test buttons on outlets.
-
Plug in lamps to outlets and light switches to test for proper connections.
-
Scan for hot spots along wire runs indicating connection issues. Address any found.
-
Verify expected voltage at receptacles. 120V typical, 240V for some.
-
Check new circuits for proper amp loads and any tripped breakers.
-
Rewire any Problem areas uncovered during testing before full energization.
Thorough testing like this allows you to uncover and address any wiring miscues made before the system goes fully live.
Staying Safe During and After the Rewiring Project
Some final tips for staying safe throughout and after a home rewiring project:
-
Turn off all power and re-verify wires are dead before working each day. Never assume.
-
Keep hands dry and wear electrical gloves and other PPE when handling wiring.
-
Use fiberglass ladders and insulated tools for additional protection.
-
Avoid working while tired or rushed to prevent costly errors.
-
Get all work permitted and inspected by the local jurisdiction to ensure code compliance.
-
Add arc fault and GFCI outlets to protect from fires and shocks per modern code.
-
Clearly label the electrical panel with any wiring changes made for future reference.
-
Consider installing whole home surge protectors and lightning rods for additional safety in electrical storms.
Rewiring a home yourself can potentially save thousands of dollars if done properly. But safety should always be the top priority. Follow these tips, take it slow, double check everything, and you can successfully rewire without getting zapped!